Linear Gauge Sensors Onosoki GS-6713A, GS-6730A, GS-6813A, GS-6830A

Ngày đăng: 09/29/2021 - 647 lượt xem

Giá: Liên hệ

Xuất xứ:
Tình trạng:
Model:
Bảo hành:

Số lượng:

Mua hàng

Hotline:

Hotline: 0365930441

Mô tả sản phẩm
Thông số kỹ thuật
Chi tiết dòng sản phẩm
Tài liệu kỹ thuật

Specifications

Model name Item	GS-6713A	GS-6730A	GS-6813A	GS-6830A
Measurement range	13 mm	30 mm	13 mm	30 mm
Resolution	10 μm		1 μm
Accuracy (at 20 °C)	3 μm	3 μm	2 μm	3 μm
Maximum spindle velocity^*1	1(4) m/s		0.3(1.2) m/s
Measurement force(downward)^*2	1.3 N or less	1.9 N or less	1.3 N or less	1.9 N or less
Number of sliding times (proven in our endurance test)	6.5 million times or more
Protection class (not including connector part)	IP64
Stem diameter	Ø15 mm^+0-0.009
Power supply	4.5 to 5.5 VDC
Power consumption (5 VDC)	120 mA or less
Signal output (5 VDC)	Two-phase square wave, phase difference: 90° ±20° Output voltage Hi:4.5 V or more / Lo:0.4 V or less
Output impedance	Approx. 22 Ω
Vibration resistance (when the power is off)^*3	147 m/s² in each of the three axial directions (75 minutes per each), 10 cycles of 10 Hz to150 Hz sweeping
Shock resistance (when the power is off)^*3	1470 m/s² in each direction for each of three axes, three times for each of the ±X,Y and Z directions, sine half-wave, pulse duration 6 ms
Operating temperature range	0 to +40 °C
Storage temperature range	-10 to +55 °C
Cable length	Approx. 1.9 m
Weight (including cable, connector)	Approx. 250 g	Approx. 310 g	Approx. 250 g	Approx. 310 g
Accessories	Instruction manual, spanner

*1. When used with Ono Sokki's Gauge Counter. The values within parentheses () are the maximum spindle velocity used with the DG-4140/DG-4190/DG-5100/DG-3000.
*2. An attachment may not return completely if it is facing upwards.
*3. Vibration/shock resistance values described in above are not guaranteed during measurement operation.
• Disconnected or modified signal cable is not applicable to CE marking.

NOTE:Please check an attaching portion (material, grounding etc.) before you install the New GS series. If the New GS series is installed in a metallic portion that is not grounded, it might cause blowout of a fuse or cable damage because of a potential difference that might be produced between a counter side chassis and a sensor side chassis.

List of Signal cable / accessory

Long life type

GS-4713A/4730A

10 µm resolution

GS-4813A/4830A

1 µm resolution

Linear Gauge Sensors

Vibration resistant structure, dust-proof, water-proof and oil-proof IP66G

• Ball spline bearing greatly improves bearing strength. The number of sliding times has tripled compared with the existing model.
•Protection class IP66G
•Performances of vibration resistance and shock resistance are two times higher than those of basic type. They enable speeding up of tact time and flexible response to on-site working environment.