Bộ chuyển dữ liệu Magnescale Interface MG10-P1, MG10-P2, MG20-DK, MG20-DG, MG20-DT, MG30-B1, MG30-B2

Ngày đăng: 14/49/2019 - 796 lượt xem

Giá: Liên hệ

Số lượng:

Mua hàng

Hotline:

Hotline: 0365930441

MG10series Specifications
*1 Total power of modules connected to MG10 should not be over 54W (12VDC Input) or 108 W (24VDC Input).
		MG10-P1	MG10-P2
Power	Power supply Power supply voltage	DC12～24V(11～26.4V)Min. startup time: :100ms or less
	Power consumption	2.0W +total power consumption for connected modules^*1
	Imrush current(10ms )	10Aor less(when maximum number of modules are connected)
	Power supply reverse connection prevention	Fuse(5A fuse is built in.)
Communication	I/F input/ output circuit	RS‐ 232C(Conforms to EIA-232C)
	Baud rate setting	2400/9600/19200/38400 bps(set with DIP switch)
	Data length	7/8bit(set with DIP switch)
	Stop bit	1/2bit(set with DIP switch)
	Parity	None/ODD/EVEN(set with DIP switch)
	Delimiter	CR/CR+LF(set with DIP switch)
Linkage function	Maximum number of linkages	max.16(total of counter modules64)
Linkage function	Maximum length of linking cable	max.10m
I/O
	Input format	source input(+COM)	sink input(-COM)
	Input format	Photo coupler insulationDC 5～24V
	Output format	sink type(-COM)	source type(+COM )
	Output format	Photo coupler insulationDC 5～24V
	Input signal	reset, pause, start, latching, and data out trigger to whole channels
	Output signal	integrated alarm
Connectable modules	Counter modules	MG20-DK, MG20-DG, MG20-DT (available for mixed use, up to 16 modules)^*1
Connectable modules	Interface modules	MG30‐ B1, MG30‐B2^*1
Accessory	LZ61: Link cable (1m)

MG20series Specifications
2 Set the resolution value of the connected gauge. 3 MG20-DG work only connect to DL**BR series
Model		MG20-DK	MG20-DG	MG20-DT
Power consumption		1W+total power consumption for connected measuring units	1.4W(when connected DG-B series) 0.5W(when connected DL-B series)	0.8W
Measuring unit input	Connectable measuring units	DKseries(A/B quadrature input)	DGB series, DLB/DL**BR series	DT series
	Allowable resolution setting^*2	10/5/1/0.5/0.1μm	10/5/0.5μm	5μm(DT12/32) 1μm(DT512)
	Allowable resolution setting^*2	set with DIP switch
	Maximum response speed	Subject to the specification of the connected gauge		1m/s
	Maximum accelation speed	Subject to the specification of the connected gauge		2400m/s²
	Reference point^*3	REF-LED (reference point loaded) shows on the display after the reference point is detected. Set "0" or preset value on the counter when the reference point is detected.		-
Others	Alarm	S-ALM LED activates by excess speed / acceleration of measuring unit. C-ALM LED activates by excess speed of the internal circuit of counter.
Others	Alarm	Alarm display is cancelled by reset command from MG10 or with the reset button of main unit.

MG30series Specifications
Model		MG30-B1	MG30-B2
Power consumption		1W
I/O	Input format	source input(+COM)	sink input(-COM)
	Input format	Photo coupler insulationDC 5～24V
	Output format	sink type(-COM)	source type(+COM)
	Output format	Photo coupler insulationDC 5～24V
	Input signal	DRQ / channel address / measuring mode shifting / comparator shifting / reset / start / posing / reference point loaded
	Output signal	BCD data (6 digits) / READY / code / GO/NO GO output / alarm / reference point loaded
Output setting		timer (1~128ms) / OUT / OR / polarity (set with internal DIP switch)

MGseries specifications
Magnescale reserves the right to change product specifications without prior notice.
Operating temperature/humidity	0～+50℃(non condensing)
Storage temperature/humidity	-10～+60℃(20～90%RH)